Aftermarket parts cost less for a reason.

Today I had a Toyota Tacoma client pop in for an oil change. I see this truck about 4 times a year for service needs. The client keeps the truck clean and up to date on all service needs. A year ago the truck was in fender bender and the OE headlights got crunched. The client came in with some aftermarket headlight units and had us install them. I mentioned that the aftermarket plastics don’t hold up in the Arizona heat. The client said he saved a lot of money and they look fine to him. I installed them.

14 months later they look like poop! The plastics are hazed over, but not on the outside. This issue is on the inside, you can not fix an inside issue. You have to replace them again. The end story is the aftermarket parts are less expensive because they are a lower quality part. They kinda look the same, but upon close inspection, they are not.

Aftermarket parts are a problem. Many do not fit correctly, plus the over all finish work is not OE level and they do not last as long. When ever I can, I try to get the client to see the value in using factory parts when ever possible. This is not to say all aftermarket parts are poor quality. We use many aftermarket parts that match OE quality.

When we know that an aftermarket part is ok to use, we use them. We are always watching out for the client. In turn we do not want to use a part that will fail. If the aftermarket part can not meet our 3 year 36,000 warranty we do not want to use it.

We install 48% OE parts on clients cars.

The end game is to fix the clients vehicle correctly the first time and offer a repair that lasts.

HeyAnthonyAz.com

It’s just a fuse.

Fuses fail for one reason, they are over loaded past their amps rating.

Many times a year I have vehicle owners drive in and ask us to look at their fuses. A fuse does not fail just because it’s old. They fail due to the load placed on them. 20161117_154934_hdr.jpgOver loading a circuit with aftermarket equipment is the most common reason for a fuse to fail “blow out” In a home, you have 20161118_095112_hdr.jpgcircuit breakers that protect each circuit within the home.

Fuses in a vehicle do the same job of protecting the electrical circuit, but if they fail you must remove the bad fuse and install a new one in the fuse box. Before you install a new fuse, its important to check to see why the fuse failed.20161123_122845_hdr.jpg

(What caused the fuse to fail) Just installing a fuse without looking for the reason it failed is not going to fix the problem. The second most common reason we see fuses fail is due to coins or metallic junk getting into the 12V aux/lighter socket. 20161118_094915_hdr.jpgI have found ear rings, small tokens, and paper clips stuck in the 12V power sockets. A direct short to ground will cause a fuse to fail instantly. 20161121_124842_hdr.jpgOnce you remove the junk from the socket the fuse can be replaced. At our service desk we offer free 12V socket to USB power adapters to plug into the open 12V sockets, just to prevent issues like junk or coins from getting into the socket and shorting the terminals in the socket
.

A 110V inverter to power a laptop can over load an accessory fuse circuit. 20161123_134347_hdr2.jpg.jpgYou do not want to use an inverter larger than 150 watts on a 15 amp fused circuit. Most basic 12V sockets only have a 15 amp fuse to power the socket, and its easy to pop a fuse with an inverter, cell phone, and GPS navigation all plugged in at the same time.

 

HeyAnthonyAz.com – It’s all good under the hood.

 

A/C Cabin Air Filter Ford Taurus “very dirty”

Service and Repairs – A/C Cabin Air filters

20161114_113741_hdr.jpgFilters protect your car from harmful debris that can cause damage to internal moving parts. The engine, and transmission need service regularly to keep them alive and happy. So what about you, the driver? Back in the mid 80’s some European car manufactures started adding air filters to the A/C system. Mercedes-Benz called it a particulate filter and it protected the A/C evaporator core from getting contaminated with hair, lint, leaves, and other nasty things that could get pulled into the air intake of the A/C system. It also protected the inside of the car from dust and oder. Most of all, the clean air was a benefit to the driver. European cars started using “Cabin Air Filters” first, around the mid 80’s. In the late 90’s I started to see them in high-end Japanese cars, and by the mid 2000’s almost all cars had some type of Air Filter added to the A/C system. The filter works great till, till it looks like the one in the picture. A filter can only do its job if it can catch and hold the dirt. This filter is past its way past its prime. looking at it, you might think it’s very old, but it’s only 3 years old, but the car is only used in town and in 3 years has only driven 7,000 miles.20161114_113734_hdr.jpg

Most car manufactures today list a 1 year or 15,000 mile interval for A/C Cabin Filters. Many car owners do not follow the recommended filter intervals. It’s hard enough to get clients to do regular oil changes much less service the A/C filter on schedule.

I have removed filters that had so much junk in them that they have collapsed in-ward and the A/C system is trying to suck them into the air intake. Blower motor failures can occur due to a plugged Cabin Air Filter. Low duct air flow can happen due to a dirty filter. Poor cooling and compressor failure can also occur because the filter is plugged up with dirt.cropped-Dirty-cabin-air-filter-heyanthonyaz.com-2941.jpg

The filter to the right is from a Toyota. The owner did not know that the car had a filter. It was an original filter. This filter is only 2 years old, and is nasty! The air flow from the duct was almost nothing, even on a high-speed. Changing the filters and servicing your car regularly is part of owning a car. Planning for repairs and preventative maintenance keeps your car happy and reliable. No one likes to tow their car to a repair shop, much less shell out money to repair something major, when you could have prevented the break down all together with a well visit to the car doctor.www.heyanthonyaz.com 252

It’s all good under the hood. HeyAnthonyAz.com

Yep, it’s broken; Plastics…

Plastics, they don’t last forever.

Unhappy owners with broken cars arrive at my shop every month, and the owners just do not understand why the car has broken down. Well, if you drive it, it will wear out…..

Todays autos use lot’s of plastics. Auto makers have always used plastic parts, but in todays cars and trucks plastic parts are used for so many things, it can be frustrating when parts don’t last because they are made of plastic.wp-image-33241149jpg.jpg

Today I have a Nissan Frontier in the shop with a coolant leak at a plastic fitting on the heater core. This is a common thing on a vehicle that is 10 years old or older.

The hard part is informing the client that the engine is bad, because it over heated, due to a plastic part that failed. Using plastics to make a car lighter, and get better emissions is great, but at what cost to the client. I would rather have all cooling system parts made from metal. The auto maker makes the parts out of plastic because it’s cheaper to manufacture.

So what do they care if the part fails and the engine goes bad. That’s why they make new cars anyway.

Fix it right, fix it once. HeyAnthonyAz.com

Can I bring my own parts?

When you go to a restaurant, do you bring your own food?

Every month, I have at least 5 people ask if we will install a part they bring in.

Our answer is no.

   It’s not that we do not want to put on your parts. It’s because of the warranty. If we sell you the part, it will come with a 2 year 24,000 mile warranty, and labor is covered 100%

If you bring in your own part, you get no warranty with us, and if the part fails, you pay the labor again to replace the part a second time.

Do we bent the rule? Some times. We have installed clients parts, depending on what the part is, and if it’s for a specialty reason like a classic car or super hard to find part, but they must sign a waiver, stating they understand the repair comes with no warranty, parts or labor.

Think about it, do you save that much?

Fix it right, Fix it once. HeyAnthonyAz.com

Helping a friend

Recently when helping a friend with an issue that they had, a problem came up. Poor communications caused a falling out. Communication is just that, and sending information via email or texts is no way to solve any issue. I am a detective and when talking to a person on the phone, I will have Q&A that will help sort out the real issues from the garbage.

I have people ask me all the time for help with an automotive problem they have. They want free advice, or they think it will be cheaper because they know me. I try to get everyone to visit the shop, so I can look at the vehicle properly. In many cases I do not charge to look at the issue at hand.

At my shop we do not charge for inspecting the vehicle if you do the repair on the same visit.

Everyone lies about whats happening with their car, it may be a small white lie, or it could be a big lie to cover up a mistake they made when trying to repair the car on their own.

Being deceptive does not save you money on the repair!

The vehicle will tell the truth, and I talk to cars all the time. The car will not hide whats wrong. It’s broken and need repair. That is why I want to look at the vehicle. Testing and getting reading from the vehicle will tell me what repairs are needed, and it will be 100% correct.

When some one wants a price for a repair sight-un-seen, it’s a guess. So, if I give someone a repair quote without inspecting the vehicle it will always be higher than normal. Brake repairs are the most commonly asked questions. The range of pricing is so wide, its scary.

Guessing at the repairs needed will cause big issues. Bring your vehicle in and let’s inspect the issue the right way, so the correct repair is done right the first time.

Heyanthonyaz.com 2015

Adjust it till it fits?

Hack Jobs Happen…

I see some crazy short cut repairs (hack jobs). “Hack jobs” by owners, shade tree mechanics and approved auto repair shops. Then I wonder why, why try, why risk a comeback. Why take the short cut in the first place. Why risk loosing a client when the hack job fails, leaving the vehicle owner stranded on the side of the road.

A hack job will fail, it’s a sub-standard repair.

 

Today I had an odd repair issue pop into the shop. Ronda had a fuel pump replaced on her 1995 Chevy Suburban about 30 days ago in Sedona Arizona. The truck has a 5.7 TBI fuel injected engine. (Throttle Body Injection System) Ronda only had one issue with the repair, the fuel economy was reduced by 30 to 40% and this was noticed right after the pump was installed. The shop that installed the pump had double checked the fuel system, and said nothing was wrong.

Ronda had moved to Sedona last year.

The client (Ronda) use to live right around the corner from our shop, but had moved to Sedona in 2013. Ronda happened to be in the valley for some doctors visits, so Ronda stopped in to see if we had time to look at this issue.

Testing showed the fuel system was running too rich. The scan tool (a computer that talks to the car’s computer) showed that the PCM (the car’s computer) was subtracting a lot of fuel. The engine computer uses a pair of fuel trim ratio numbers to display fuel system compensation (larger number = more fuel added to the engine Or a smaller number = less fuel, fuel reduced to the engine). A repair technician can view the fuel trim numbers “live” as they update (in real-time) and watch how the system is operating, rich, lean or normal.

Next I attached a gauge used to test fuel pressure to the engine’s fuel system. The fuel pressure gauge showed that the fuel system pressure was around 19 PSI of pressure. (Why?) The TBI system specification is 9 to 12 PSI. So why was the PSI so high?

I suspected it had the wrong fuel pump installed. So, I removed the fuel pump and found a big mess. What I found was a major issue, the person that did the repairs, must have had a huge loss of reasoning. The part was clearly the wrong part for the truck. When I entered the pump part number into a parts jobber, part interchange system. I discovered the part was the wrong pump for the truck.

The shop decided to adjust the wrong part till it would fit in the tank. But wait, that’s not all. The pump was for a 1996 5.7 MPI engine. (Multi Port Injection System) not a 1995 5.7 TBI system. The 1996 MPI system runs at 60 to 66 PSI. This is clearly too much pressure for the system to handle. To bleed off the high PSI. The shop that made the repairs, had removed the hose clamp to the PSI fuel coupling hose that connects the fuel pumps outlet pipe to the metal pipe going out to the engine’s fuel injector’s. Plus the old fuel pump harness was installed on the new pump, and the electrical connector had a broken retaining clip.

The adjustments and compromises should have never happened, but they did.

Just buy the correct part, and if the part arrives wrong, get the correct part. The correct part was available in Flagstaff, less than a 2 hour round trip from Sedona. The client had already waited 5 days, what was one more day to get the right part.

We fixed the truck and it is running correctly, with the correct part. The client is happy and the mileage is back to normal. Plus Ronda will be bringing her truck to us when ever she is in town every 3 to 4 months.

Keeping up on the needs of an older vehicle may seem costly, but if you do the math. The right older vehicle can be cost-effective in the long run. Every vehicle needs repairs someday, new or old.

It’s all good under the hood, heyanthonyaz.com 2014

www.carfax.com How accurate is the service?

Buying a used car can drain your savings, if you buy the wrong one.

In the last 10 months I have preformed 35 pre-purchase inspections, 27 cars and 8 trucks. Every vehicle had a clean carfax report. 5 of the cars and 1 of the trucks had un-reported major accident damage. They all looked fine on the outside, looking good, like nothing was wrong.

Carfax is only as good as the people who report the accident damage.

If the vehicle owner has accident repairs fixed for cash, under the table, by a discount shop. The accident damage will never be reported to carfax.

This type of repair may be hidden from view and the only thing you can do, is to make sure you do not buy any vehicle without an inspection. If the vehicle owner does not want you to take it and have it inspected, do not buy it!

You work hard for your money and it would be horrible to find big dollar repairs after you just paid a big chunk of money for what you thought was a nice used car.

Even if the vehicle has a clean carfax report and a good story about why the owner is selling the car. Get all the facts, get it into a shop for a full inspection!

The money you spend for the inspection will give you peace of mind. No one wants to buy a lemon.

It’s all good under the hood. www.HeyAnthonyAz.com 2014

Tony’s Service Center 5362 North 16th St. Phoenix, AZ 85016

4 months or 4000 miles

Oil Change Interval

A new car will not need as much attention as a car with 120,000 miles, but new cars will have service needs too. Just because its new is not a reason to over look good service habits.

The simple method for regular oil changes; New vehicles, up to 3 years of age or 40,000 miles, will mostly need basic services, oil changes, fluid top off’s and tire rotations. Follow the normal service intervals in the owners hand book, and you will be doing great.

Regular motor oil Intervals can range from 3,500 to 7,500 miles. Full synthetic oil services can range from 7,500 to 15,0000 mile intervals.

Some repair shops, like Tony’s Service Center, have switched to Heavy Duty blended motor oils for our oil change packages.

What is a blend? It’s a mix of regular motor oil and synthetic oil. It’s a better product, and it protects your engine better than a regular motor oil.

All new vehicles sold, come with a owners hand book.

Most owners do not read it cover to cover, its boring stuff. In the back of the book, it lists your service and maintenance needs from 0 miles to 120,000. Servicing intervals are-listed two ways. Normal service and Severe service, most cars will fall into the Normal service area.

Life after 40, “the honey-moon is over.”

Vehicles older than 3 years or with 40,000 to 120,000 miles; Ok, parts are starting to wear out. Belts, Hoses, Brakes, Batteries and Tires are the most common repair needs.

Major fluids will need replacement services, and you will still have basic oil changes to do, so continue to follow the normal service intervals in your vehicle hand book. Your vehicle is starting to show its age. Prompt maintenance and repairs will prevent break downs…

NOTE; Fluid servicing is a big part of a vehicles long life. No fluids are life time. Some car makers will say they have life time fluids. GM found out painfully, that Dex-Cool, a life time coolant, was a very bad idea. “No fluids last the life of the vehicle.”

~~~~~~~~~~~

My car only has 33,000 miles on it…

Just because your vehicle has 33,000 miles on it, does not indicate that it’s in new condition. A 12-year-old car that has 33,000 miles on it, will still need service just like a car that has 120,000 miles on it. ( It’s all about ) “Time in Service”

Vehicles over 8 years old or 120,000 and up; It’s time to step up the service intervals to severe service. Why? The vehicle is getting older and will need more services to keep it in top condition. “More repairs, more services, more love.”

How does regular servicing prevent break downs?

Having a trusted repair shop looking at your vehicle is essential to keeping your vehicle in top condition. Jumping from shop to shop is no good.

Having the same shop looking at your car will allow them to watch your needs. Loyalty will help the shop give you advice that is correct for your needs. Plus your service advisor can show you how to budget for future repairs.

It’s all good under the hood. HeyAnthonyAz.com 2014

 

 

Stop!

*** If your engine is over heating, STOP! ***

Today I had a vehicle Towed in from the other side of town. The client lives near my shop, but works 30 miles away. The car had over heated on his way to work. He was only 7 minuets away from work, so the client continued to drive the car to work.

If you are driving along and the “red over heating light turns on” or you see the gauge in the RED! ***Stop the car safely and turn off the engine.***

Do not continue to drive the vehicle!

The engine has just over heated! shut down the engine to prevent over heating damage!!!

When an engine is over heating, it can cause major damage to the aluminum parts inside the engine.

Many of todays engines have lots aluminum parts. Aluminum parts are strong as long as they do not get too hot.

When aluminum parts gets super hot, the aluminum will expand a lot. Aluminum parts can crack as they cool back down from being over heated.

The other thing that happens when the aluminum parts expand, is the gaskets sealing the engine can be crushed or compressed during the over heating. When the engine cools down it can start leaking from the damaged gaskets.

Engine over heating can also cause big issues with plastic parts bolted to the engine, and plastic radiators.

Running an engine just a couple of extra minuets, can destroy an engine quickly. Many of todays newer vehicles have engines that can cost up to 6,000.00 just for an engine.

That is big money!

If the gauge is in the red or the red engine light is on, shut the engine off ASAP. Stop and call a Tow truck.

A Tow into the shop for repairs is nothing compared to an engine replacement.

My client was not happy, the engine was damaged from the over heating. Next week we will be installing a new engine.

It’s all good under the hood. HeyAnthonyAz.com 2014